Our Story

Reactor Products
Reactor billet flexplates
Billet SFI 29.1 flexplates since 1984

Born in a race car.
Built since 1984.

How a Funny Car racer’s problem became the Reactor billet flexplate.

01

Born in a race car. Built since 1984.

Reactor began with a racer’s problem, not a marketing brief.

Olan Teves was racing Funny Cars when cracked stock components gave him a reason to rethink what sat between the engine and transmission. He heard the noise, removed the damaged OEM flexplate and worried about what a failure could mean with the driver so close to the drivetrain. His answer was to develop his own replacement billet flexplate. That work became Reactor Products.

Since 1984, Reactor’s story has been rooted in drag racing and the billet flexplate.

The Big Kahuna Corvette Funny Car in Drag Racing’s “Built for Fun” feature, November 1985.
The Big Kahuna Corvette Funny Car in Drag Racing’s “Built for Fun” feature, November 1985. Drag Racing magazine, Nov. 1985 (“Built for Fun”); photos Bob McClurg
02

A racer before a brand

Olan’s racing story reaches back before Reactor. His racing years include a 1938 Chevrolet, later Chevrolet race cars, and the ex-Stone, Woods & Bones AA/GS Mustang.

Then came the Funny Car years and the Big Kahuna. Olan chose the name. The Charger-bodied car and a later Corvette-bodied version were the cars behind the company’s early development work.

Research and development testing on the Corvette Funny Car showed that using the inertia ring on the billet flexplate improved reaction time and 60-foot times, with an elapsed time of 7.82 seconds at about 174 mph.

The Big Kahuna, a 1973 Dodge Charger, at Orange County International Raceway, November 4, 1978.
The Big Kahuna, a 1973 Dodge Charger, at Orange County International Raceway, November 4, 1978. Photo: Mark Hollenstein (via Draglist)
The Charger-bodied Big Kahuna at OCIR, April 17, 1982.
The Charger-bodied Big Kahuna at OCIR, April 17, 1982. Photo: Mike Ditty (via Draglist)
03

The Vega

Extensive research and development testing was also done on the 1977 Vega Super Gas car. The Vega was a four-link car with a 427 big-block punched or bored out to 440 cubic inches, and a Powerglide. Testing included various inertia-ring weights: a 2-pound, a 4½- to 5-pound, and an 8-pound ring. The 4½- to 5-pound ring worked best on that car. Using the inertia ring improved reaction time and 60-foot times.

A yellow race car on a drag strip, lettered REACTOR PRODUCTS on the door and OLAN TEVES on the side window, carrying the number S/G 724. A light-blue race car numbered 798 stands in the next lane. A white and red tower behind them shows signs reading Winston Finals, Winston Drag Racing, Pomona Raceway, and NHRA. A person in a red helmet and a striped shirt stands at the rear of the yellow car.
The 1977 Vega Super Gas car. Photo courtesy Olan Teves
04

Why “Reactor”?

Asked why he chose the company name, Olan pointed to reaction time with the inertia ring. The name carried the purpose of the project: exploring how a billet flexplate and an optional inertia ring could be used in a racing combination.

He places the business start in 1984 and made an early version about a year before that.

The bolt-on inertia weight ring, as shown on the 2000 website.
The bolt-on inertia weight ring, as shown on the 2000 website. Reactor Products (reactorproducts.com, 2000)
The REACTOR PRODUCTS trademark: first use October 1, 1984; registered May 29, 2001.
The REACTOR PRODUCTS trademark: first use October 1, 1984; registered May 29, 2001. USPTO TSDR public filing, Reg. No. 2,454,834
05

Built through development

The early work involved more than one design. An early design was a one-piece flexplate made with chrome moly material with a broached gear, and a later move to aluminum because of flexibility and torsional harmonics.

He also distinguishes an initial approach to NHRA from later SFI work. The first testing revealed that the ring gear did bow due to the inertia force between three retaining tabs, leading to a nine-tab design. That is a description of early development, not directions for modifying a billet flexplate.

NHRA approved the billet flexplate, and on January 29, 1988, SFI tested and approved the Reactor billet flexplate.

Allan Bechtloff of Hank the Crank helped with balancing fixtures.

By March 1986, Drag Racing magazine had featured Reactor in Tim Marshall’s “Flexplate Eliminator” article. Its account described billet aluminum construction, CNC machining, and an optional inertia ring that could be changed to suit track conditions.

Drag Racing magazine cover, March 1986.
Drag Racing, March 1986. Drag Racing magazine, March 1986 (as shown on reactorproducts.com, 2000)
Headline and billet flexplate photograph from “Flexplate Eliminator,” Drag Racing, March 1986, p.37.
“Flexplate Eliminator,” Drag Racing, March 1986, p.37. Drag Racing magazine, March 1986, p.37, “Flexplate Eliminator” by Tim Marshall
06

The people and places behind the work

Olan operated Reactor first in Torrance and later in Gardena. Oren Orr helped machine early parts on an engine lathe and a manual mill. Glengarry Manufacturing Inc., the company that acquired Norm Hill’s Riverside business, subsequently contributed machining work.

Olan also made a flexplate shield for a time before discontinuing them.

07

From Chevrolet roots to a broader range

The early magazine account focused on GM automatic applications. The billet flexplate range later broadened to Chevrolet, Ford, Mopar, Buick-Pontiac-Olds and AMC, followed by an import announcement in 1998. Custom work was part of the offering as well.

Billet flexplates for Chevrolet, Ford, Mopar and Buick-Pontiac-Olds from the 2000 product page.
Billet flexplates for Chevrolet, Ford, Mopar and Buick-Pontiac-Olds from the 2000 product page. (AMC was offered too.) Reactor Products (reactorproducts.com, 2000)
reactorproducts.com/mainProducts.html · Sep 26, 2000
reactorproducts.com products page, September 26, 2000, showing the full product line.
Sep 26, 2000 · Products page, full product line. Wayback Machine capture of reactorproducts.com.

The website followed in 1999, giving racers another way to find Reactor’s products and information. A new online store followed in 2025.

08

Carrying the idea forward

Olan wants Reactor’s work to continue into its next chapter.

Today’s Reactor story continues with the billet flexplate, built to SFI 29.1. Reactor appears on SFI’s 2026 participating-manufacturers list for SFI 29.1. That listing does not, by itself, date the first certification or certify a particular part number.

Reactor billet flexplates today.
Reactor billet flexplates today. Reactor Products
A solid billet blank in the CNC.
It starts as solid billet. Reactor Products
A billet flexplate on the CNC.
A billet flexplate on the CNC. Reactor Products

The heart of the story is this: a racer saw a problem, developed his own answer, and built a brand around the billet flexplate.

Explore Reactor billet flexplates by engine family, or learn about SFI recertification.

Shop Billet Flexplates SFI Recertification Find a Dealer